Brand | TAG Heuer |
Caliber Number | 16 |
In-House? | No |
Base Caliber | ETA/Valjoux 7750 (or Sellita SW500) |
Movement Type | Automatic, self-winding mechanical, chronograph |
Jewels | 25 |
Lignes | 13.25”’ |
Diameter | 30mm |
Height | 7.9mm thick |
Power Reserve | ~48 hours |
Vibrations Per Hour | 28,800 vph, 4 Hz |
Lift Angle | 49 degrees |
Anti-Shock System | Incabloc |
Regulator System | ETACHRON with fine tuning |
Chronograph System | Three-plane cam style |
Rotor Type | Ball bearing system |
Rotor Winding Direction | Uni-directional (clockwise) |
Hand Windable? | Yes |
Manual Winding Direction | Clockwise |
Hand Sizes | 2mm x 1.2mm x .25mm + 3 x .18mm (needs confirmed) |
Features | Central hours; central minutes; central chronograph seconds; small seconds subdial at 9:00; 30 minutes counter at 12:00; 12 hours counter at 6:00; day-date or date only at 3:00 |
Hacking Seconds? | Yes |
Country of Manufacture | Switzerland, Swiss made |
Service Interval | ~5 years |
Known Models | TAG Heuer Carrera Calibre 16 Chronograph (Please add your watches to comments below…) |
The TAG Heuer Calibre 16 is a Swiss made automatic chronograph watch movement with 25 jewels and a frequency of 28,800 bph. This caliber is basically either an ETA 7750 or Sellita SW500 with a custom branded rotor.
Some of the topics covered in this caliber listing:
When did TAG switch from ETA 7750 to Sellita SW500?
Early models using the Cal. 16 will be powered by the ETA 7750 (such as the example pictured above). Later, when ETA movements became unavailable to watch brands outside of the Swatch Group, companies like TAG Heuer started using the next best Swiss made alternative: the Sellita SW500 (ETA 7750 clone movement).
TAG documentation started showing the Calibre 16 being based on ETA 7750 or SW500 a least as far back as 2014.
However, the exact date or serial numbers when this switch happened is unknown, therefore you will simply need to check your watch to figure out which one you have.
At the time of this post, there do not appear to be any mentions of “SW500” anywhere on the TAG Heuer website. In current TAG stock photos, part of the engraved Sellita logo can be seen under the balance wheel (to the right of the fine tuning regulator in the image below):
How to know if a Calibre 16 is ETA or Sellita based?
The easiest way to tell which base caliber your Calibre 16 is using, is to check the engraving located on the mainplate under the balance wheel. The example pictured on this page is an ETA 7750 base.
Another thing to look for is the fine-timing adjustment on the regulator assembly:
Setting the Time:
To set the time on your Calibre 16 powered TAG Heuer watch, pull the crown out two clicks to time-setting mode. If your watch is equipped with a screw-down crown, be sure to unscrew it first. With the crown in time-setting mode, turn it clockwise or counterclockwise to the desired time.
Setting the Calendar:
Extremely Important Note: Do not attempt to set the day or date on your watch while the hands are set between the hours of 7pm and 3am. You may see other sites say 10pm and 2am, but ETA officially states:
“Rapid date and day correction is not possible between 8 p.m. and 2 a.m.” -Source ETA 7750 Technical Communication
Just to be on the safe side, be as far out of that range as possible (just in case the hands weren’t installed exactly at 12am). If you set the day and day within those hours, the automatic calendar system is engaged to advance the datewheels to the next day and there is a chance to break something – even if nothing breaks, you may still cause the date to switch over at something like 6am rather than 12am.
To set the day/date on your caliber 16 watch read the extremely important note above first. Pull the crown out one click to calendar setting mode. Turn the crown clockwise (away from you) to set the date and counterclockwise (towards you) to set the day of the week.
Chronograph start/stop/reset:
Button sequence: Top, top, bottom.
- Top button: Start/Stop
- Bottom button: Reset
Chronograph Hand Lining Up:
Unlike quartz powered chronograph movements, mechanical watches do not have the luxury of using a reset sequence to get the chronograph hand to line up to 12:00. If the chronograph hand on your caliber 16 powered watch is not lining up, it could be a mechanical problem and should be inspected by a professional watchmaker. Your watch may need serviced or the hand might need to be reinstalled.
Is it OK to Leave the Chronograph Seconds Constantly Running?
It is not recommended to leave the central chronograph sweeping second hand in a constantly running or engaged state. With the way the gear train is set up on the cal. 16, this could add extra and unnecessary wear and tear. Additionally, by doing so your watch will experience a change in amplitude, leading to a loss of power reserve and accuracy.
Examples of watches with this movement:
The Calibre 16 can be found in Tag Heuer Carrera Chronograph models.
Original versions with the aluminum bezel insert (ref: CV2A10) were powered by the ETA 7750 (although it is unconfirmed whether any aluminum versions were produced with the SW500).
Newer ceramic bezel models (ref: CBN2A1AA) seem to be powered by the Sellita SW500:
Pros and Cons:
Pros:
- Based on 7750/SW500 makes it serviceable without having to send your watch to the manufacturer
- Solid, reliable workhorse movement
Cons:
- Service costs can be expensive for automatic chronograph movements
- 7750’s finicky day/date setting (you must remember to move the hands into the safe zone first)
Additional Resources:
Recent Comments
I really wish that you would stop spreading the false information that the C07.111 etc.…
Found in Bulova Super Seville Day Date
Mine is very stiff.
Hi Xcaliber, various tap sizes are available. Tap size refers to the diameter of the…
Why two stems? 35117/tap10 or 351892/tap 11
Squale Y1545 GMT 30 Atmos Tropic
Aragon has been bringing back this movement.. this is the 45mm DiveMaster Titanium with full…