Miyota 0S10 quartz movement in Skagen watch

Miyota Caliber 0S10

Miyota 0S10 quartz movement in Skagen watch

Manufacturer Miyota
Caliber Number 0S10
Type Quartz
Replaces Caliber Citizen 0510
Size 13.50”’ (30.80mm) diameter x 4.13mm thick
Battery Cell Number SR927W
Frequency 32,768Hz
Quartz Type Tuning fork type quartz crystal
Stem 065-453
Hand Sizes 120/80/18
Jewels 0
Functions Hours, minutes, seconds, chronograph, date
Country of Manufacture Japan
Known Models
Skagen, Invicta (add yours in the comments below…)

Miyota caliber OS10 is a quartz watch movement with zero jewels. It is made in Japan.

Accuracy Rating

Miyota states the accuracy of the caliber Os10 quartz movement to be +/-20 seconds/month.

Replacement Price

Replacement prices for the Miyota caliber 0S10 movement were found in the range of $25.00 – $31.95 USD.

There is also a caliber 0S1A (if you know the difference please comment below).

Additional Resources:

Is the Miyota Caliber 0S10 any good? Share your opinions, experiences and watches below... Remember to keep comments respectful and follow our community guidelines.

32
Leave a Reply

avatar
  Subscribe  
newest oldest most voted
Notify of
Val
Guest
Val

No jewels?!

Kool
Guest
Kool

Is this watch in my Invicta?

Bill Goodman
Guest

It is in my Invicta.

Bill
Guest

Seems there is no way to ‘reset’ the chronograph minute ‘sub hand’ or the ‘Hour Sub hand’ (to zero). the only thing that can be RESET is the sweep second hand. this seems strange?? anyone have other info on this?

Jan Janoušek
Guest

they say my Caterpillar (watch) DT.163.20.211 has this type of movement, but I am not watch-pro, so I am not sure 100% 🙁

Adel M Elnashar
Guest
Adel M Elnashar

fossil ch-2442 as well

Abdul samad suratwala
Guest
Abdul samad suratwala

I was interes in this coplete watch were can i gate

Steve
Guest
Steve

Which watch are you looking for?

Anthony Elgan
Guest

Anybody know if there is an automatic movement this size that would take the same hands from the Miyota Caliber No. OS10? I’m curious if I can do a movement swap in a Jack Mason chronograph I have. Does Miyota make an automatic chrono movement? I ask this before I’ve done much digging, so my next step is to start looking for movements with the same dimensions. I’m only looking at Miyota movements because I’m hoping the hand sizes are compatible, but I’ll look into that too. Could be a fun project.

Martin
Guest
Martin

Gentlemen,

the question arose how to ‘reset’ the chronograph minute ‘sub hand’.
OK it´s a while since but the info may be of future interest.

I posted an inquiry directly to Miyota how to accomplish this but did not get any answer yet.

Obviously there is no feature to ‘electrically’ reset the minute sub hand.

Here is the solution that worked for me:
Dismantle the movement from the watch case,
then GENTLY push the minute sub hand to its zero position
(the hand snaps by discrete tick marks).

This procedure applies to the Miyota 0S20 movement as well.

Regards
Martin

Dan
Guest
Dan

Thanks for the info. What did you use to push the sub-dial hand (being careful not to touch the dial)?

A Rose
Guest
A Rose

How much is this watch worth?

Bennett
Guest
Bennett

This movement is in my Capri watch. Performs perfectly!

Bennett
Guest
Bennett

Miyota OS10 in Capri watch

PHD
Guest
PHD

All Casio analog watches that show module # 2328 on the case back use the Miyota 0S10 movement
One example is the Casio EF 503D

Dan
Guest
Dan

I figured out how to calibrate the minute hand. It is not so simple as just pressing the ‘B’ button in time-setting mode. You have to press ‘A’ so that the stopwatch seconds hand advances, and then that allows you to press ‘B’ to advance the minute hand. The B button cannot be pressed without pressing A first.

So once you calibrate the minute hand you can adjust the seconds back to 0. If only this was made clear in the instructions for my watch (Casio EF503D).

Dan
Guest
Dan

Ok never mind, that was just a fluke. After fiddling with the buttons the stopwatch minute hand fell off.

Luis Santos
Guest
Luis Santos

I tried to replicate the techinique on my 0S20, without success. After several years I still can’t figure out how to adjust the chonograph minute hand. Only with Martin’s “brute force” idea..

Randall Thomason
Guest
Randall Thomason

Did you get it calibrated?

Allen
Guest
Allen

Greetings gentlemen. Life is good but sucks when you cant get your to work 🙂 I need help and i pray i can get some from any of you fine gentlemen. I have a watch that uses Miyota 0510 movement, I managed to remove crown etc but am finding it tough to get the moment out. it seems to be stuck? I try prying it gently at the point where it says “pry Up”. alas, it did not even budge. I’m too afraid to use too much force. Am i doing it wrong? Any help would be most appreciated. Thanks… Read more »

Randall Thomason
Guest
Randall Thomason

Did you get it out? Be careful prying, I did that once and it chipped the edge of the paint on the dial. Luckily it was covered by an internal bezel, but still I wasn’t pleased about it at all. Try to flip the case over on your hand and try to see if the movement falls into your hand. That’s how I usually do it. It needs to be exactly a round circle for it to fit through the hole of the case. That’s why prying doesn’t work unless the watch brand did a shabby job of designing the… Read more »

Allen
Guest
Allen

Thank you for your respond Randall. Nope, i’ve not got it out yet. I tried everything, even tapping on the crystal, but to no avail. It doesn’t have any plastic holding it down either. Wish i could upload a pic. Geez!!